• 製品応用

  • 技術文献
  • The Importance and Insurance of ESD Protection

The Importance and Insurance of ESD Protection

2020/03/02

What is electrostatics?

Electrostatic discharge(ESD)exist in our daily life. This is the phenomenon that free charge transfer between objects. Inevitably, we usually encounter the following phenomena, especially in cold and dry winter. For example: We will hear the pop, pop, pop sound when wearing sweater; the hair will float up when we comb hair; we will feel electric shock when touching doorknobs or other metal objects. ESD may just bring out some noise, but it may also make us feeling pain.


What cause electrostatics? [1][2]

In nature world, all objects are composed of particles known as molecule and it will keep electrical neutrality. Molecules are composed by one or more atoms. Atom is composed of proton with a positive elementary electric charge, electron with a negative elementary electric charge and neutron with no net electric charge. Usually, the number of protons and the number of electrons are the same, so the object will keep electrical neutrality. When the object being affected by external energy, for example, objects become electrically charged after they come into frictional contact with a different material object. One will lose electrons to be positively charged, while the other will get the same number of electrons to be negatively charged. To be positive charged or negative charged is depending on material, surface roughness, temperature, and other parameters. If the charge is hard to neutralize while object separating, the charge will accumulate to bring objects with electrostatics. Refer to fig. 1, when fur and plastic come into frictional contact, then electrons transferred from the fur to the plastic, so the fur will be positive charged, while the plastic will be negatively charged. [3] In addition to triboelectric effect, induction electrification is another way to make a charged object. 

Figure 1.

Figure 1.


Refer to fig. 2 [4], when a charged object is close to the uncharged metal ball, the metal ball will be attracted by induction, and then we connect this uncharged metal ball to GND, electrons will flow from metal ball to GND or (flow from GND to metal) depend on the charged object is negative charged or (positive charged). Now we disconnect the metal ball to GND, the metal ball will be positive charged or (negative charged). 


Figure 2.


When charged objects come into contact with the conductor, because the object will tend to be electrically neutrality, so resulting current. This phenomenon could lead to thousands of volts and makes electronic products that we use damaged.


The importance of ESD protection

In 1947, John Bardeen and Walter Brattain observed that when two gold point contacts were applied to germanium, the output signal’s power is greater than the input ones. This was the first transistor which was fabricated. The first metal oxide semiconductor field effect transistor (MOSFETs) was invented by Dawon Kahng and Martin Atalla at Bell Laboratory in 1959. Since that, germanium was largely replaced by silicon. Therefore, silicon has formed the basis of the semiconductor industry almost since its birth. According to Gordon Moore's observation, the number of transistors on integrated circuit (IC) doubles approximately every eighteen months. This is famous ‘Moore's Law’. Continue to shrink each component in an integrated circuit can allow more complex circuit in the same area or an equally complex circuit in a smaller area. This achieves the effect of reducing costs. 


In order to increase integration of IC and reduce unit costs, devices continue to shrink in Complementary Metal Oxide Semiconductor (CMOS) process, but this accompanied with reliability problems. One of shrink is to get gate dielectric layer thinner and thinner. As we know, the gate dielectric layer is composed of oxide and oxide will breakdown when the applied electric field is about 10 MV/cm. So when the gate dielectric layer becomes thinner, the value of breakdown voltage of gate dielectric layer getting smaller and smaller. It will increase the probability of failure more easily by electrostatic discharge. Nowadays, Electronic products posses more and more functions, the corresponding input/output port (I/O port) also increase, resulting in easier interference or damage IC by ESD. The manufacturing costs, product quality and reliability, as well as company's profits will be affected due to ESD failure. That is the reason why importance of ESD protection increasing. Fig.3 shows Return Materials Authorization (RMA) in various fields, the reasons which ESD and EOS caused are as much as 58%. This information shows that we still have much to do in electrostatic protection. [5] 


Figure 3.

Figure 3.


ESD test models [6]

The problem of ESD damage to electronic products is not always easy to solve. When ESD suddenly strike to electronic product which is under normal operation, it may become unstable or it may recover when we reset, even worse it may also damaged due to the IC inside cannot withstand ESD voltage or current.


Because of the difference of ESD generation and the discharge type to IC, the test models are currently classified into the following three: 

1. human body mode (HBM) 

2. machine mode (MM) 

3. charge device model (CDM)


Human body mode: Because of the body movement, friction or other factors on the human body and then electrostatics accumulate. When this person touches the IC, electrostatics on the human body will discharge into the IC via pin, and then discharged to ground pin. Ampere rating of the instantaneous discharge current can be generated a few hundred nanoseconds (ns), and the internal IC may be destroyed. Fig. 4 shows I-t curve under HBM mode.


Figure 4.

Machine mode: It is easier occurs in automatic control process, equipment like robot itself accumulates electrostatics. When this equipment touches the IC, electrostatics on the equipment will discharge into the IC via pin, and then discharged to ground pin. Because equipment are almost made by metal, so effective resistance of equipment is 0 Ω. The discharge time of MM mode is shorter compare to the discharge time of HBM mode, thus causing damage to the IC is also more serious. Ampere rating of the instantaneous discharge current can be generated about few nanoseconds to tens of nanoseconds, and the internal IC may be destroyed. Fig. 5 shows I-t curve under MM mode.


Figure 5.


Charge device model: Due to friction, induction or other factors, the electrostatics will be accumulated in IC, but the IC is not damaged. If this charged IC touch ground, the electrostatic current will discharge out from the pin. The discharge time of CDM mode is even shorter compare to the discharge time of MM mode. Ampere rating of the instantaneous discharge current can be generated about few nanoseconds. The amount of accumulation electrostatics will change due to effective capacitance of IC. How we dispose IC like angle and location or package of IC will change the effective capacitance of IC, so it is hard to simulate this discharge mode. Fig. 6 shows I-t curve under CDM mode.


Figure 6.


ESD Test Specification 

Table 1 show IEC 61000-4-2 standard for system level testing that replicates a charged person discharging to a system. The standards are defined 2kV, 4kV, 6kV and 8kV. Nowadays, systems typically require achieving Level 4. Table 2 show the product features to be affected after ESD test. Results are classified in to four categories. Criteria A: product can be normal operated during and after ESD test without exceptional event. Criteria B: the function of product will decline or fail during ESD test, but can automatically recover after ESD test. Criteria C: the function of product will decline or fail during ESD test, and need operator intervention to reset, so the function of product will recover after ESD test. Criteria D: the product will lose its function, and the function cannot recover even reset. Only criteria A and criteria B are qualified, criteria C and criteria D are unqualified. [7]


Table 1.

Table 1.


Table 2.


The basic concept of ESD protection

The electrostatic discharge protection circuit is made to protect IC.  The electrostatic discharge protection circuit provides ESD discharge path in order to avoid electrostatic current flows into the integrated circuit and damage the IC. Electrostatic discharge protection circuit configured as Fig. 7, it connect in parallel with the IC which we want to protect. [8] Under normal operating conditions, the electrostatic discharge protection circuit will present a high impedance state so that current can normally flow into the internal IC, although there will still be small leakage current flows through the electrostatic discharge protection circuit, but ideally we can regard electrostatic discharge protection circuit as an open circuit. When there appears abnormally high voltage, electrostatic discharge protection circuit will be quickly turned on to provide a low impedance path, so the current can pass through electrostatic discharge protection circuit to avoid large current damage the internal IC. Also electrostatic discharge protection circuit will also clamp voltage at a certain interval to avoid gate oxide of internal device breakdown at high voltages. 


Figure 7.


How to choose the electrostatic discharge protection circuit

Fig.8 shows the ESD design window of an IC [8]. VDD is power supply voltage, Vh is holding voltage, Vt1 is trigger voltage, and VBD is oxide breakdown voltage. The design window of ESD protection circuit must be inside the blue dash line. First, the minimum clamping voltage of ESD protection circuit must be higher than VDD, otherwise the IC which we want to protect may latch-up or the ESD protection circuit may be mis-triggered under normal operation. Vt1 is the minimum voltage to turn on the ESD protection circuit, therefore Vt1 must be lower than VBD, otherwise gate oxide of device in IC will breakdown before the ESD protection circuit turn on. The turn on resistance (Ron) of ESD protection circuit should be minimized to reduce the joule heat generated in the ESD protection circuit and the clamping voltage of ESD protection circuit during ESD stress.


Figure 8.


Reference 

[1] https://en.wikipedia.org/wiki/Electrostatics  

[2] http://www.baike.com/wiki/%E9%9D%99%E7%94%B5  

[3] http://activity.ntsec.gov.tw/web/show.asp?ph10  

[4] http://www.phyworld.idv.tw/Nature/Jun_3/B5_CH4/B3_4-1_POINT.pdf  

[5] Amerasekera, E. A. and Najm, F. N., Failure Mechanisms in Semiconductor    Devices, John Wiley & Sons, New York, 1997  

[6] http://www.ics.ee.nctu.edu.tw/~mdker/ESD/index/index2.html 

[7]http://www.digitimes.com.tw/tw/dt/n/shwnws.asp?id=0000160028_COJ1T6HK      1WRFXA97F4HMK  

[8] C.-Y. Lin, P.-H. Chang, R.-K. Chang, Ming-Dou Ker, and W.-T. Wang, “Vertical SCR structure for on-chip ESD protection in nanoscale CMOS technology,” Proc. of  International Symposium on Physical and Failure Analysis of Integrated Circuits (IPFA), Hsinchu, Taiwan, Jun. 29-Jul. 2, 2015. 

メルマガ配信サービス

Send