• 製品応用

  • 技術文献
  • Integrated Common-mode Choke and TVS Combo-solution for Solving EMI/ESD Issues of the High-speed Connectors

Integrated Common-mode Choke and TVS Combo-solution for Solving EMI/ESD Issues of the High-speed Connectors

2018/11/20

Electromagnetic Compatibility (EMC) related issues are always a very tough question for electronic engineers to solve during the period of developing a new electronic product.  No matter it is about Electromagnetic Interference (EMI), Electrostatic Discharge (ESD)(IEC-61000-4-2), Electrical Fast Transient (EFT)(IEC-61000-4-4), or Surge (or, Lightening)(IEC-61000-4-5), each of these issues should be cleared to meet the test specifications before the new product has been merchandised.  Otherwise, the new product would not be able to face the customers.   


For the events of electrostatic discharge (ESD) and surge (or, lightening), their causes would be easy to be understood by the nouns themselves.  Comparing with ESD and surge, it would not be so easy to be familiar with the causes of electrical fast transient (EFT) events by simply reading the noun itself.  The causes of an electrical fast transient event could be: the switching of a power relay with inductive load, unintentionally designed continuous voltage discharge which is across the interface, transient overvoltage which is frequently higher than the supply voltage ... etc. [1].  For example, the switching transient state caused by power on/off of a motor appearing at the primary inductance of the motor would cause interference noises and feedback to the power source circuit loop.  And the sequence of transient interference noises would be spread out through the power source circuit loop.  Sometimes the transient noises could be too small and can be neglected, but, sometimes it would be too serious to interfere or damage the electronic equipments or the related PCBs.  Therefore, impulse noise suppression is a very important issue when designing an electronic circuit loop.  If the power consumption of a power system is very huge (ex. an industrial power system in a factory), the induced transient noise on the power system would be more serious and critical [2].  The EFT issue would not only appear on the power lines, but it can also be found on the input/output ports.  Table.1 shows the voltage peak and repetition rate definitions of the transient voltage swing on the power ports when doing the EFT tests [3].  Fig.1 shows the general graph of a complete period of a fast transient/burst in the time domain.  Fig.2 shows the detail definition of the waveshape of a single pulse into a 50 Ω load [3].


Table.1  Test levels [3]

Table.1  Test levels [3]


Fig.1  General graph of a fast transient/burst [3]

Fig.1  General graph of a fast transient/burst [3]


Fig.2  Waveshape of a single pulse into a 50 Ω load [3]


The developing trend of the outlooks of electronic products is to be designed as light and convenient as possible for portable/wearable usage.  So that people can grab any of the useful information for their emergent/pressing usage on the instant they need.  It is no longer like the old time: people had to look for internet service and sit down stably, then, look for the target information from the huge knowledge pool on the internet.  Due to the highly improved convenience, people can save plenty of time in their rapidly and busily daily lives.   


In order to meet the wearable targets of being convenient, electronic products have been designed to be more lighter, thinner, and smaller.  It indicates that the occupied area and spacing of the electronic elements/devices on the Printed Circuit/Wire Board (PCB/PWB) or the Flexible Printed Circuit Board (FPCB) of a wearable electronic product would be more and more smaller.  Moreover, the interconnect metal line width and spacing would also get more and more tightened, and, the PCB drawing layer number is also getting increasing from 4 layers to six/eight layers, and even more.  Therefore, the interconnect metal line length between different PCB layers, the maximum amount of used via holes in series connections, and the broken pieces of the ground plane would be all increased significantly.  If the signal integrity (SI) issue has not been well designed between different layers of a system PCB, there could be too long return path of common mode noise, or getting too close for adjacent critical nets which might cause serious crosstalk.  Beyond all these, the long series connection lines for linking devices from different PCB layers with too many via holes in series connection will make the turn-on resistance be increased.  When an ESD/EOS/EFT/Surge event appears on the mentioned long connection lines, it would be very tough to efficiently discharge the huge transient energy by the system circuits itself.  The huge transient energy might cause the system malfunction, or would even burn out some devices or interconnection lines of the system.  Hence, to choose EMI filter devices properly can help the system circuit design engineer or the EMC design engineer to reduce or even remove the electromagnetic interference and signal integrity issues effectively.  The developed EMI filter products by Amazing Microelectronic Corp. are all well designed with embedded Transient Voltage Suppressor (TVS) devices as a combo solution for the customers.  So that it not only can remove or reduce the EMI noise and improve the SI issue, it also can protection the system from crashing by the transient ESD events.   


Generally, EMI noise would be presented by two different ways.  One is the single-ended signal with coupled noises.  In other words, the signal to carry an interference noise is a single-ended signal with single input port and single output port.  Single-ended signals are the most common and simple signals.  For example, the display control signals connected to the FPCB connector of the LCD (Liquid-Crystal Display) display module of a mobile phone is very easy to be interfered by the RF signals of the RF emitter/receiver module.  Another format of EMI noise is about the differential signals with coupled common mode noise.  In ideal cases, the interference noise sources from the open field would be coupled into the differential-pair signals with the same noise amplitude and in the same phase angle at the same time.  Therefore, the noise difference between the two differential ports would be exactly 0 for the differential-pair signals, which the differential-pair signals are with the same signal amplitude but with 180-degree phase angle shift.  In other words, the noises coupled into the differential-pair signals would not affect the normal signals at all.  Therefore, the noise immunity of differential-pairs is generally much better when comparing with single-ended signals.  But, the above description is based on the "ideal cases" assumption, instead of the real world cases.  In reality, the input impedance of the two ports of a differential-pair would not be the same, the return paths of the common mode noises coupled into the two differential ports would not be exactly symmetric, and, the noises coupled into the two differential ports would not be exactly in the same phase and at the same time.  As a result, the amplitude of the common mode noise appears in the differential-pair signals would not be zero, it does exist and is large enough to affect the normal differential-pair signals.   


When the noise has been coupled into a single-ended signal, generally the system circuit design engineer or the EMC design engineer can use resistors, capacitors, inductors, or, several combinations of all these three basic components to remove or reduce the interfering noises.  For example, Fig.3 shows a 50-ohm impedance matched system which is interfered by the noise source.  The interference signal at the left side of each of the figure of Fig.3 is the noise source coupled into the right hand side impedance matched system.  In order to remove the interfering noise, Fig.3(a) simply takes a capacitor device which is in parallel connection with the right hand side impedance matched system.  In an ideal case, the effective impedance of a capacitor would be close to 0 when a transient event is applied on it.  Therefore, whenever the interfering noise has passed the 50-ohm input impedance, it would meet the by-pass capacitor with its impedance of almost 0.  So that it can sink the transient noise energy to the system ground node, instead of coupling into the impedance matched system on the right hand side.  Fig.3(b) shows the way how to use an inductor to eliminate the interference signal.  The inductor is placed between the 50-ohm input impedance and the 50-ohm impedance matched system.  In an ideal case, the effective impedance of an inductor would be very large when a transient event is applied on it.  Therefore, whenever the interfering noise has passed the 50-ohm input impedance, it would meet the inductor with very large impedance.  Then, it can block out the interference signal from coupling into the 50-ohm impedance matched system.   


The above explanations about using a simple capacitor or inductor for removing the interference signal are both based on the 'ideal' characteristics of a capacitor or inductor.  In the real world, actually the equivalent impedance of a capacitor under a transient event would not be almost 0 (short circuit), and the equivalent impedance of an inductor under a transient event would not be very large (open circuit).  As a result, the interference signal will couple into the right hand side 50-ohm impedance matched system partially.  The energy amount of the coupled noise would depend on the intensity/amplitude and the frequency band of the interference signal, and, of course, the equivalent impedance of the chosen capacitor or inductor and its high-frequency equivalent circuits.   


Except taking a simple capacitor or a simple inductor, the EMC design engineer can further use π-model EMI filter devices for more effectively eliminate the interference signal.  Fig.3(c) and Fig.3(d) show the C-R-C and the C-L-C π-model EMI filter devices.  When using the π-model EMI filter device as the solution to remove the interference signal, the performance would be better comparing with simply take a capacitor or an inductor.  The reason why is that there is an additional capacitor in parallel with the 50-ohm matched system to bypass the couple noise source for the C-R-C or C-L-C π-model EMI filter device.  Besides, the resistor or inductor of the π-model EMI filter is in series connection with the input impedance and it can also be used for blocking the noise source from interfering the 50-ohm matched system at the right hand side.

Fig.3  The ways to remove the noise interference of a single-ended signal. (a) by using a capacitor device

(a)

Fig.3  The ways to remove the noise interference of a single-ended signal. (b) by using an inductor device

(b)

Fig.3  The ways to remove the noise interference of a single-ended signal. (c) by using C-R-C π-model EMI filter

(C)

Fig.3  The ways to remove the noise interference of a single-ended signal. (d) by using C-L-C π-model EMI filter.

(D)

Fig.3  The ways to remove the noise interference of a single-ended signal. (a) by using a capacitor device, (b) by using an inductor device, (c) by using C-R-C π-model EMI filter,  (d) by using C-L-C π-model EMI filter.


If the EMI noise appears at the connector site, then, the questions to be solved would be not only the removal of the interference noise signal, but also bypassing the ESD energy for protection the internal system circuitries.  Amazing Microelectronic Corp. has already accumulated a lot of successful stories and experiences for solving ESD related issues in the electronic industry.  The EMI filter related products released by Amazing Microelectronic Corp. are designed not only with the noise filtering function, but also designed with embedded TVS devices for system-level ESD protection purpose.  So that the system circuit design engineer or the system EMC design engineer can simply take a device to accomplish the work that originally needs both an EMI filter device and a TVS device.  As a result, the PCB parasitic effects can be reduced, and also the originally occupied layout area for mounting the EMI filter and TVS devices can be reduced, which might also lead to saving the cost.  Moreover, the TVS device embedded within the C-R-C or C-L-C π-model EMI filter proposed by Amazing Microelectronic Corp. is designed to be with very low ESD turn-on resistance (Ron) and very low ESD clamping voltage (Vclamp).  That's the reason why the ESD protection performance of the related EMI filter products can be outstanding comparing with the performance of the similar products from the other competitors.   


Consequently, when the system circuit design engineer or the EMC design engineer solves the interference signal of a single-ended signal, he can simply take the CRC π-model EMI filter solutions provided by Amazing Microelectronic Corp. as an effective solution.  These π-model EMI filter products cover the applications of LCD display, camera module, SIM (Subscriber Identification Module) card input/output ports, SD (Secure Digital Memory Card) / MMC (Multimedia Card) card input/output ports of a mobile phone or a notebook computer.  Fig.4 shows an EMI issue example which is caused by the RF signal emission of the RF module of a mobile phone.  The emitted RF signal interferes the LCD display and the camera module of the mobile phone.  Then, the system circuit design engineer can take the part number of AZM-LCD05-06F C-R-C π-model EMI filter of Amazing Microelectronic Corp. to solve this issue, and also to protect the LCD display module and the camera module from the damage of the transient ESD events.

(a)

(b)

Fig.6  Part no. AZM-USB31-02F CMF product of Amazing Microelectronic Corp., (a) outlook of the IC backside pinouts, (b) the equivalent circuit for one of the differential-pair signals.


Fig.7 shows the operation principle of the TVS devices embedded within the common mode choke filter (CMF) products released by Amazing Microelectronic Corp.  When each of the differential-pair signals is normally switched between logic '1' and logic '0', there would be voltage over or under damping at the rising and falling edge of the time domain voltage waveform.  The embedded TVS devices can clamp the over or under damping voltage swing with their own device characteristics.  For the over damping voltage, the TVS devices can clamp it by their reverse breakdown voltage (VBD).  On the other hand, for the under damping voltage swing, the TVS devices can clamp it by their forward voltage (VF).  In this kind of manner, the unexpected voltage damping can be limited within the safe operation region that the system can be functioning normally.  When an ESD event is applied on one of the differential-pair input port, the TVS device can provide an efficient discharge path for sinking the ESD transient energy into the system ground, and then, further bypass to the outside large ground plane.

Fig.7  The functions of the embedded TVS devices of the CMF products developed by Amazing Microelectronic Corp.  The TVS devices will be activated when normal single-ended overshooting/undershooting noises or ESD events appear at the input ports.

Fig.7  The functions of the embedded TVS devices of the CMF products developed by Amazing Microelectronic Corp.  The TVS devices will be activated when normal single-ended overshooting/undershooting noises or ESD events appear at the input ports.


The common mode filter (CMF) products released by Amazing Microelectronic Corp. are all designed with good performance embedded transient voltage suppressors (TVS) for providing excellent ESD protection performance.  So that it can reduce the PCB parasitic effects when comparing with taking two discrete TVS devices and one common mode choke, especially for the high frequency/speed circuit applications.  During the process of soldering mount, it would introduce additional parasitic resistance, capacitance, and inductance onto the circuitries of the PCB.  Therefore, a combo CMF solution with embedded TVS devices would be better comparing with taking one CMF and two discrete TVS devices.  Besides, the CMF and TVS combo solution can also save the PCB layout area and the PCB circuit designer's design effort.  For portable/wearable products, the PCB area is pretty tighten for layout engineering.  Therefore, the combo solution is more convenient for a PCB circuit design engineer to proceed his PCB layout work.  As a summary, the Amazing Microelectronic Corp. provided CMF combo solutions with embedded TVS devices are excellent choices with several advantages.  


Reference: 

 [1]  Demos Yuan, "EN61000-4-4 Electrical Fast Transient/Burst Immunity Test," Richtec Instruments Co., Ltd., 2015. 

 [2]  S.T. Cheng, " Factory Electrical Power Supply Impulse Noise Suppression Algorithm Study," MS thesis, EECS Dept., Feng-Chia Univ., 2007. 

 [3]  IEC (International Electrotechnical Commission), "Electromagnetic compatibility (EMC) – Part 4-4: Testing and measurement techniques – Electrical fast transient/burst immunity test," CEI/IEC 61000-4-4:2004, ver. 2nd, 2004. 

 [4]  Differential Signaling, Wikipedia, 2015. URL: https://zh.wikipedia.org/wiki/%E5%B7%AE%E5%88%86%E4%BF%A1%E5%8F%B7 

 [5]  muRata, “Noise Suppression by Common Mode Choke Coils,” Doc. no. TE04EA-1, 1998.

メルマガ配信サービス

Send